Project Update

Things That Broke/Things I've Changed


So after owning the truck for 5 months, I was fortunate enough not to have any major mechanical casualties bite me.  I purchased the truck uncertified, and to get it road worthy, it needed a new parking brake cable and driver side window regulator (we'll get back to these crappy windows in a bit).  I brought it to a mechanic I knew to get those things sorted out before my temporary plate expired.  In the process of bringing this thing to his shop and back, I noticed that on cooler mornings you'd see a bit of condensation coming from the defroster vents in the dash.  While the engine temperature levels remained steady and the moisture seemed to be odorless, I shrugged it off as an electrical gremlin from the rain we had the previous night. 

Weeks later, the truck is running fine but I fine that the brand new carpet the previous owner installed was drenched in antifreeze on the passenger side.  After some desperate internet searches, I found out that the replacement part itself was relatively cheap, and the job was not bad if you knew your way around the dash.  So I ordered a new heater core from Rock Auto and swapped it in.  Getting the heater box open is probably the hardest part as there is not a lot of room to maneuver your hands and tools behind the dash.  I should also point out that the screws holding in the top of my dash pad were stripped, so I could not remove the entire dashboard.  After some some serious straining and colourful language, I was able to muscle the new heater core through the firewall and into place. 



 


Aside from that, there are many minor things I have addressed for this truck.  I've replaced the driver side inner and outer fenders with a Taiwanese-Ebay replacement (I admit that I thought they were OEM until I noticed they were lighter and thinner, but who am I kidding? -weight reduction bro!).  The original fenders appeared nice on the outside, but the inner wells were completely rotted, and I swore I could've seen the paint bubbling worse every time it rained.  The new fender fits okay, but it needed some careful massaging to get in. I also undercoated the inner wells so I've got my fingers crossed that they will hold up nicely.  The passenger fender will have to wait until next spring.

So stay tuned for that shit show!



I've replaced the OEM mirrors with Ebay chrome mirrors, which are not the greatest quality, but I think the aesthetic trade off is worth it.  I also changed the tail light lenses to chrome for the same reason and to get rid of some moisture.  I learned the hard way, that the pickup lights from the S-10 and the Sonoma actually have different mounting locations than the SUV lights like mine.  So I had to relocate the mounting locations by drilling into the plastic shell.  Other than that, I've applied Bondo and rust paint in various locations just to get it to hold out for a winter before I attempt to graft the rot with fiber-glass some time next spring.

Here's where I complain about these older power windows.  I spent 200+ dollars getting my mechanic to diagnose and fix my tumbling window problem, which I now realize was really really stupid on my part.  Replacing a window regulator will not fix a tumbling window, but these old GM cars use these stupid little plastic clips that snap into the molded metal window frame of the door.  They are supposed to ensure the window rises and lowers vertically.  However, after years of use and exposure to the elements, plastic gets pretty damn crusty.  Not to mention the adhesive at the bottom of the window that is binding it to the rail that pulls it down, loses its stickiness, so you are left with a window that either won't roll down, and later falls down on its own, or one that comes off the rails like mine.  The clips are literally 5 cents each off Rock Auto and that solved the problem in one afternoon. 



So moving on, I also added auxiliary Hella driving lamps.  They work great, and I actually took the time to wire it properly and neatly but had to undo all of that after the truck developed a misfire during a road trip.  I freaked out and thought my newly wired lights may have been causing an electrical mishap, only to find out much later that it wasn't the case.



The misfire happened during a trip down to Cayuga Ontario for the Canadian Sport Compact Series Finale.  You may or may not see that coverage here in the future.  Anyways, it was a real scorcher despite being a mid-September day.  I was accompanied by a friend who brought his Kawasaki Ninja 300, so we blasted down a few regional roads southeast of Ancaster.  I noticed a little bit of jolting when the truck was going over inclines but thought nothing of it.  On the way home, it became obvious that the little V6 wasn't happy.  It would shake and misfire on any change in throttle position, whether it was accelerating from a dead stop or increasing throttle to climb a hill.  It was missing so hard I could see the oil pressure bounce.  So I ended up driving on the misfire for weeks until I found the time to tear apart the EGR and give it a thorough cleaning. 

Call it beginners luck, but of all things that could've been the culprit - this has solved the problem.  This is purely from internet lore, but what was probably happening was the EGR (exhaust gas re-circulation) valve was stuck in the open position due to excessive carbon buildup.  And believe me, there was a ton of soot in the thing, and judging by force I had to put into un-bolting it, I don't think anyone has serviced it in the vehicle's lifetime.  Anyways, a stuck EGR valve essentially re-circulates too much exhaust back into the intake, which leans out the air fuel ratio to a point the engine ends up missing. 

Here is where I am also dumb; I failed to buy a new gasket before servicing the EGR, so naturally the old gasket had disintegrated into thin air and I bolted my freshly cleaned unit back on to the engine only to be greeted with a ticking noise.  The ticking would go away at idle but became loud, and sped up as I accelerated.  Once again scouring the internet, I found that an exhaust leak can cause this noise.  Perhaps some sort of pulsation of the gasses escaping.. I have no clue but I had tear the EGR off again to toss on my new 3 dollar gasket from NAPA and she's run like a dream ever since.




Lastly, I had the starter replaced at Canadian Tire as it wasn't fully engaging the flywheel every start.  It got to a point where I could hear it fragging teeth off the flywheel.  I should've known this was going to be a problem as a brand new Champion starter had been included in the pile of parts I bought the truck with.

The Impression

Maintenance

Well it has treated me well since I've owned it.  Every headache was also an opportunity to learn and experiment.  I also performed the first oil change in my ownership and was pretty glad to see that the oil was pretty consistent.  No metallic particles, and thick globs of carbon I've seen on some other cars.  At least I can go to bed at night knowing that the motor isn't eating itself alive.  The previous owner had put synthetic in it so I went ahead and got some 5W-30 synthetic high mileage oil and a Mobil 1 filter for good measure.  Being a 4x4 model, the skid plate actually gets in the way of the oil draining and splashes it everywhere, but other than that the plug and filter were easily accessible.

Quirks

Approaching 30 years in age, you can't expect it to be showroom fresh despite it's low mileage.  The truck burns a little oil when it is cold, but quickly cleans itself up when things get up to operating temperature.  Speaking of warming up, it takes a VERY long time.  I allow myself up to 10 minutes to warm up the motor before I head out.

How does it drive?  It takes a firm foot and steady hands.  I guess we are spoiled with the electronic throttle and steering in the modern cars such as my folk's 2012 Camry LE, but the cable actuated throttle takes some foot pressure, and you need a bit of forearm strength to wrestle the thing around a corner at speed, even with power steering (but we all know how to get stronger forearms amirite?)  The brakes are a combo of discs in front and drums in the rear, and is optioned with ABS in the rear.  With that being said, this is a 3500+ lb vehicle without any passengers and needs some time for the dated brakes to do their job, so yes the brake pedal is firm but I often find myself sinking into it more than I'd like to in an emergency.  The engine is powerful but not very willing.  It's low end torque pushes off from a dead stop very well, so well it can chirp the 235/75/15 All Terrains - On a closed course obviously.  Above 3000 rpm, nobody is home.  To give you an idea, this engine redlines at 5000 rpm.  The slushy 4 speed automatic shifts well when accelerating from a stop, but don't expect to be winning any roll races.  I often find myself outside of the power band when attempting a freeway merge or pass - so extra time is needed.  The ride is bone jarring over the smallest ruts in the road and there are plenty of squeaks and rattles from the loose fitting interior panels.

Some advantages are that it is actually pretty small compared to modern "compact" SUVs.  The short wheelbase and narrow body make it easy to maneuver in tight parking lots, and the huge rear windows/side glass allow for worry-free reversing.  There are also very few blind spots as the pillars in this vehicle are really narrow.

Some shortcomings include it's fuel economy and lack of safety.  This thing drinks gasoline like you wouldn't believe, especially in the city where the overdrive gear isn't really being used.  On a good trip I can get about 350 km in the city at up to the mid 400s on the highway with a massive 76 liter tank.  It also has no airbags whatsoever, which in theory should make for a quick and painless death and those thin pillars I mentioned earlier also doesn't inspire much confidence in my well-being after a rollover, but hey - all the more motivation to be a safer driver!

Thanks for bearing with me for this long post, that was 5 months of blunders with this marvel of GM engineering.  I hope to update more frequently with shorter and hopefully better news, cheers!




Comments